الرئيسية Discharge Mufflers HPEOK PKX Refrigeration Discharge Mufflers – PKX-4022 and PKX-4026

HPEOK PKX Refrigeration Discharge Mufflers – PKX-4022 and PKX-4026

سعر التخفيض $46.00

عرض السعر أولاً، ثم الدفع بعد التأكيد. أسعار المنتجات لا تشمل الشحن. لا يلزم أي دفع لإرسال الطلب.

طريقة الطلب:
1) في سلة التسوق، اختر «المتابعة إلى طلب الشراء» وأرسل الموديلات والمواصفات والكميات وعنوان التسليم الكامل (البلد والرمز البريدي).
2) نؤكد التوفر والإجمالي شاملاً الشحن ومدة التسليم التقديرية.
3) بعد موافقتك على الإجمالي، نرسل رابط الدفع الخاص بطلبك في Shopify بالبريد الإلكتروني.
4) ادفع عبر الرابط؛ نرتب الإرسال بعد استلام المبلغ كاملاً.
إرسال الطلب لا يعني اكتمال عملية الشراء. مواعيد التسليم تقديرية.

سياسة الشحن
Model: PKX-4022 - 1-3/8 in ODF
إضافة إلى قائمة الأمنيات
إضافة إلى المقارنة
التوفر: متوفر في المخزون
HPEOK PKX Refrigeration Discharge Mufflers – PKX-4022 and PKX-4026

HPEOK PKX Refrigeration Discharge Mufflers – PKX-4022 and PKX-4026

Product Description

HPEOK PKX discharge mufflers help reduce pressure pulsations and the associated noise in refrigeration compressor discharge lines. Installed downstream of the compressor, the muffler uses internal baffles and expansion chambers to dampen pulsating refrigerant gas flow.

This selection includes PKX-4022 with a 1-3/8-inch ODF connection and PKX-4026 with a 1-5/8-inch ODF connection. Both models have a catalogue body diameter of 102 mm and body-length dimension B of 280 mm. Their connection sizes and overall lengths differ, so the complete model code should be retained when ordering.

Pulsation and Noise Reduction

The internal baffles and chambers allow the discharge gas to expand and change its flow velocity, helping dampen low- and high-frequency gas pulsations. The series is designed to provide this damping with a low pressure drop.

A discharge muffler addresses noise caused by gas pulsation. Mechanical vibration transmitted through the pipework requires suitable vibration isolation as part of the system design. The manufacturer recommends installing a vibration absorber between the compressor and muffler.

The referenced catalogue does not publish a guaranteed decibel-reduction figure, acoustic frequency-response curve or numerical pressure-drop curve. Selection should therefore consider the compressor and discharge-piping arrangement.

Model Selection and Dimensions

Model ODF Connection Corresponding Tube OD* Overall Length A Body Length B Body Diameter D
PKX-4022 1-3/8 inch 34.925 mm 368 mm 280 mm 102 mm
PKX-4026 1-5/8 inch 41.275 mm 380 mm 280 mm 102 mm

The millimetre tube-OD values are mathematical conversions of the inch sizes, rather than separately published metric socket-bore dimensions.

The ODF connections are intended for brazed copper-tube installation. Use the original factory drawing to interpret dimensions A, B and D and check the available installation space.

The manufacturer recommends selecting a muffler connection size that matches or exceeds the compressor discharge-line size. The catalogue does not provide a compressor-horsepower or refrigeration-capacity selection table for these two models.

Pressure Rating and Operating Temperature

The exact-model specification table lists a pressure rating of 3.2 MPa, equivalent to 32 bar, for both PKX-4022 and PKX-4026.

The general series introduction in the same catalogue states 34 bar. Because these entries differ, this listing uses the model-table value of 32 bar. Confirm the current supplied-unit rating against its nameplate or manufacturer documentation before final selection.

The allowable operating temperature in the 2020 catalogue is −40°C to +130°C. The source provides this operating range without separate fluid and ambient temperature limits.

Refrigerant and Oil Applications

The manufacturer identifies HCFC and HFC refrigerants and their associated oils. It also refers to other industrial fluids that are non-corrosive to steel and copper.

Provide the actual refrigerant, oil and operating conditions when requesting a quotation so that application suitability can be checked. Compatibility with another refrigerant family must be confirmed separately.

Flow and Installation

The catalogue identifies bi-directional flow for the PKX series. Mounting orientation must still allow oil drainage and limit oil collection inside the muffler.

Follow these manufacturer installation recommendations:

  • Install close to the compressor and before the oil separator.
  • For horizontal or angled installation, keep the labelled side at the top centre.
  • A slight slope with the outlet below the inlet helps oil drainage.
  • Vertical installation is also permitted in the catalogue notes.
  • Install a vibration absorber between the compressor and muffler.
  • On parallel compressor racks, a muffler may be installed in the common discharge line or individually for each compressor, depending on system design.

Follow the instructions supplied with the actual unit and provide suitable pipe support and vibration isolation.

Technical Specifications

Parameter Specification
Brand HPEOK
Series PKX
Product Type Refrigeration Discharge Muffler
Available Models PKX-4022 and PKX-4026
Main Function Reduction of discharge-gas pressure pulsations and associated noise
Internal Operating Principle Baffles and expansion chambers
Installation Location Compressor discharge line, before the oil separator
Connection Type ODF brazed connection
Connection Sizes 1-3/8 inch and 1-5/8 inch
Flow Bi-directional, according to the catalogue
Model-Table Pressure Rating 3.2 MPa / 32 bar
Allowable Operating Temperature −40°C to +130°C
Catalogue Refrigerant Applications HCFC and HFC refrigerants and associated oils
Body Diameter 102 mm for both models
Body-Length Dimension B 280 mm for both models
Overall-Length Dimension A 368 mm / 380 mm, depending on model
Mounting Positions Horizontal, angled or vertical, following installation requirements
Guaranteed Sound Attenuation Not published on the referenced pages
Weight and Internal Volume Not published on the referenced pages
Exact Material Grade and Wall Thickness Not published on the referenced pages

Ordering Information

Please provide the required model, quantity, compressor model, refrigerant, oil type, discharge-line size, operating pressure and temperature, installation orientation and delivery destination.

For replacement applications, include photographs and measurements of the existing unit and available installation space.

Model

PKX-4022 - 1-3/8 in ODF, PKX-4026 - 1-5/8 in ODF

منتجات شاهدتها مؤخرًا