HPEOK PKX Refrigeration Discharge Mufflers – PKX-4022 and PKX-4026
Сначала согласуйте предложение, затем оплачивайте. Цены товаров не включают доставку. Для отправки заявки оплата не требуется.
Как заказать:
1) В корзине нажмите «Перейти к заявке на заказ» и укажите модели/характеристики, количество и полный адрес доставки (страна и индекс).
2) Мы подтвердим наличие, общую сумму с доставкой и примерный срок.
3) После согласования общей суммы отправим ссылку Shopify для оплаты по электронной почте.
4) Оплатите по ссылке; отправка организуется после полной оплаты.
Отправка заявки не завершает оформление заказа. Сроки доставки ориентировочные.
HPEOK PKX Refrigeration Discharge Mufflers – PKX-4022 and PKX-4026
Product Description
HPEOK PKX discharge mufflers help reduce pressure pulsations and the associated noise in refrigeration compressor discharge lines. Installed downstream of the compressor, the muffler uses internal baffles and expansion chambers to dampen pulsating refrigerant gas flow.
This selection includes PKX-4022 with a 1-3/8-inch ODF connection and PKX-4026 with a 1-5/8-inch ODF connection. Both models have a catalogue body diameter of 102 mm and body-length dimension B of 280 mm. Their connection sizes and overall lengths differ, so the complete model code should be retained when ordering.
Pulsation and Noise Reduction
The internal baffles and chambers allow the discharge gas to expand and change its flow velocity, helping dampen low- and high-frequency gas pulsations. The series is designed to provide this damping with a low pressure drop.
A discharge muffler addresses noise caused by gas pulsation. Mechanical vibration transmitted through the pipework requires suitable vibration isolation as part of the system design. The manufacturer recommends installing a vibration absorber between the compressor and muffler.
The referenced catalogue does not publish a guaranteed decibel-reduction figure, acoustic frequency-response curve or numerical pressure-drop curve. Selection should therefore consider the compressor and discharge-piping arrangement.
Model Selection and Dimensions
| Model | ODF Connection | Corresponding Tube OD* | Overall Length A | Body Length B | Body Diameter D |
|---|---|---|---|---|---|
| PKX-4022 | 1-3/8 inch | 34.925 mm | 368 mm | 280 mm | 102 mm |
| PKX-4026 | 1-5/8 inch | 41.275 mm | 380 mm | 280 mm | 102 mm |
The millimetre tube-OD values are mathematical conversions of the inch sizes, rather than separately published metric socket-bore dimensions.
The ODF connections are intended for brazed copper-tube installation. Use the original factory drawing to interpret dimensions A, B and D and check the available installation space.
The manufacturer recommends selecting a muffler connection size that matches or exceeds the compressor discharge-line size. The catalogue does not provide a compressor-horsepower or refrigeration-capacity selection table for these two models.
Pressure Rating and Operating Temperature
The exact-model specification table lists a pressure rating of 3.2 MPa, equivalent to 32 bar, for both PKX-4022 and PKX-4026.
The general series introduction in the same catalogue states 34 bar. Because these entries differ, this listing uses the model-table value of 32 bar. Confirm the current supplied-unit rating against its nameplate or manufacturer documentation before final selection.
The allowable operating temperature in the 2020 catalogue is −40°C to +130°C. The source provides this operating range without separate fluid and ambient temperature limits.
Refrigerant and Oil Applications
The manufacturer identifies HCFC and HFC refrigerants and their associated oils. It also refers to other industrial fluids that are non-corrosive to steel and copper.
Provide the actual refrigerant, oil and operating conditions when requesting a quotation so that application suitability can be checked. Compatibility with another refrigerant family must be confirmed separately.
Flow and Installation
The catalogue identifies bi-directional flow for the PKX series. Mounting orientation must still allow oil drainage and limit oil collection inside the muffler.
Follow these manufacturer installation recommendations:
- Install close to the compressor and before the oil separator.
- For horizontal or angled installation, keep the labelled side at the top centre.
- A slight slope with the outlet below the inlet helps oil drainage.
- Vertical installation is also permitted in the catalogue notes.
- Install a vibration absorber between the compressor and muffler.
- On parallel compressor racks, a muffler may be installed in the common discharge line or individually for each compressor, depending on system design.
Follow the instructions supplied with the actual unit and provide suitable pipe support and vibration isolation.
Technical Specifications
| Parameter | Specification |
|---|---|
| Brand | HPEOK |
| Series | PKX |
| Product Type | Refrigeration Discharge Muffler |
| Available Models | PKX-4022 and PKX-4026 |
| Main Function | Reduction of discharge-gas pressure pulsations and associated noise |
| Internal Operating Principle | Baffles and expansion chambers |
| Installation Location | Compressor discharge line, before the oil separator |
| Connection Type | ODF brazed connection |
| Connection Sizes | 1-3/8 inch and 1-5/8 inch |
| Flow | Bi-directional, according to the catalogue |
| Model-Table Pressure Rating | 3.2 MPa / 32 bar |
| Allowable Operating Temperature | −40°C to +130°C |
| Catalogue Refrigerant Applications | HCFC and HFC refrigerants and associated oils |
| Body Diameter | 102 mm for both models |
| Body-Length Dimension B | 280 mm for both models |
| Overall-Length Dimension A | 368 mm / 380 mm, depending on model |
| Mounting Positions | Horizontal, angled or vertical, following installation requirements |
| Guaranteed Sound Attenuation | Not published on the referenced pages |
| Weight and Internal Volume | Not published on the referenced pages |
| Exact Material Grade and Wall Thickness | Not published on the referenced pages |
Ordering Information
Please provide the required model, quantity, compressor model, refrigerant, oil type, discharge-line size, operating pressure and temperature, installation orientation and delivery destination.
For replacement applications, include photographs and measurements of the existing unit and available installation space.
| Model |
PKX-4022 - 1-3/8 in ODF, PKX-4026 - 1-5/8 in ODF |
|---|





